This anchor can be used on posts from 75mm-90mm  wood posts on decks, stairs, patios, concrete or any other hard surfaces.

This is non engineered anchor and should not be used on decking which is higher then 60cm above ground level, Please use TD001 for this.

You can use the skirts below on either 90mm posts or 100mm post. 

A 25mm dia. hole saw (48mm inside depth) is required to prepare post with a circular pilot cut to guide cutting edge of tube which is then driven into anchor as shown in installation video.

Please note the core left by the hole saw forms part of the strength so please don't use a normal drill. 

Not recommended for older, drier wood (m.c. 12% or less)or with knots in lower 200mm of post. Works best with “green” new lumber with moisture content of 15%-25%.

Not intended for use with hardwoods or Douglas Fir unless hardwood installation techniques are used as indicated in directions. This is just powder coated unlike the TD001 which has been galvanized as well. 

fastener package (3/8x5 lag bolts and #14x3 screws) which are included in this package.

Max spacing between posts 1.8m.

Price: £12.75 each

Two piece snap post skirt to fit 100mm x 100mm posts covers anchor and fasteners for a completely concealed appearance can be used on TD001 and TD009.

You can install them before or after construction.

Made of durable metal, hot dip galvanized and black powder coated.

Price: £8.30 each

Two piece snap post skirt to fit 90mm x 90mm posts covers, anchor and fasteners for a completely concealed appearance can be used on TD001 and TD009.

You can install them before or after construction.

Made of durable metal, hot dip galvanized and black powder coated.

Price: £8.30 each

Two piece snap post skirt to fit 90mm x 90mm post, covers anchor and fasteners for a completely concealed appearance can be used on TD001 and TD009.

You can install them before or after construction.

Price: £12.00 each

Use this 32mm diameter hole saw and arbor to prepare the ends of posts for use with our Titan post anchor TD001. Depth of cut is 48mm.

 Use the circular hole cut as a pilot guide for the anchor tube which is 3.5" long. Drive the tube and base flush to post with a 3 lbs mallet.

It is always a good idea to sharpen the end of the tube so that it goes in easier. 

Arbor requires a 1/2" chuck.

Price: £15.00 each

Use this 25mm diameter hole saw and arbor to prepare the ends of posts for use with our Titan post anchor TD009. Depth of cut is 48mm.

 Use the circular hole cut as a pilot guide for the anchor tube which is 3.5" long. Drive the tube and base flush to post with a 3 lbs mallet.

It is always a good idea to sharpen the end of the tube so that it goes in easier. 

Arbor requires a 1/2" chuck.

Price: £15.00 each

To use with 142mm x142mm (5 1/2'' x51/2'') wood posts on decks, stairs, patios, concrete or any other hard surfaces.

A 1.75" dia. hole saw (1-7/8" inside depth) is required to prepare post with a circular pilot cut to guide cutting edge of tube which is then driven into anchor as shown in installation video.

Not recommended for older, drier wood (m.c. 12% or less)or with knots in lower 200mm of post. Works best with "green" new lumber with moisture content of 15%-25%.

Not intended for use with hardwoods or Douglas Fir unless hardwood installation techniques are used as indicated in directions. Hot dip galvanized and powder coated for superior performance.

Tested and approved according to IRC (AC273) and CBC building code procedures for use in residential guards for one and two family dwellings.

Must use specified fastener package (3/8x5 lag bolts and #14x3 screws) which are included in this package.

Max spacing between posts 1.8m.

Price: £22.30 each

Two piece snap post skirt covers anchor and fasteners for a completely concealed appearance.

You can install them before or after construction.

Made of durable metal, hot dip galvanized and powder coated black.

Price: £8.30 each

Two piece snap post skirt covers anchor and fasteners for a completely concealed appearance.

You can install them before or after construction.

Made of durable metal, hot dip galvanized and powder coated black.

Price: £14.00 each

Use this 1-3/4" diameter hole saw and arbor to prepare the ends of 142x142posts for use with our Titan post anchor. Depth of cut is 1-7/8

Plunge the hole saw to a depth of 1-7/8". Use the circular hole cut as a pilot guide for the anchor tube which is 4.5" long.

Arbor requires a 1/2" chuck.

Price: £15.00 each

This powder coated extruded aluminium baluster with polycarbonate fixings  makes fitting balusters to decking  a snap a screw driver and tape measure are all you need,

Screw the connectors to the railing put the locking rings on each end snap the balusters in place and slide the locking rings over the top.

Use 95mm CLS timber top and bottom with 100mm gap at the bottom to make up the right height. 

The spacing's are 11 cm at either end and 12cm centre to centre (10cm gap between bars maximum).15 balusters per 1.79 meter run. 

The kit contains 10 baluster and 20 snap connectors along with screws,

Price: £38 per kit. Will split box on request cost will be £4 per baluster please email.